stm32 驱动 TFT LCD－Changing's Blog

LCD/LCM的基本概念

    液晶显示器(Liquid Crystal Display: LCD)的构造是在两片平行的玻璃当中放置液态的晶体，两片玻璃中间有许多垂直和水平的细小电线，透过通电与否来控制杆状水晶分子改变方向，将光线折射出来产生画面。它包括了TFT,OLED,UFB,TFD,STN等类型的液晶显示屏.

    LCM(LCD Module)即LCD显示模组、液晶模块，是指将液晶显示器件，连接件，控制与驱动等外围电路，PCB电路板，背光源，结构件等装配在一起的组件。 购买相应的LCD Module时，会提供相关驱动IC资料，很多会有驱动代码。不过价格会比单买 LCD显示屏贵很多。

LCD显示模式

    LCD的接口有多种，分类很细。主要看LCD的驱动方式和控制方式，目前手机上的彩色LCD的连接方式一般有这么几种：MCU模式，RGB模式，SPI模式，VSYNC模式，MDDI模式，DSI模式。MCU模式（也写成MPU模式的）。只有TFT模块才有RGB接口。

    MCU模式

        因为主要针对单片机的领域在使用,因此得名.后在中低端手机大量使用,其主要特点是价格便宜的。MCU-LCD接口的标准术语是Intel提出的8080总线标准，因此在很多文档中用I80 来指MCU-LCD屏。主要又可以分为8080模式和6800模式，这两者之间主要是时序的区别。数据位传输有8位，9位，16位，18位，24位。

MCU接口标准名称是I80，管脚的控制脚有5个：

CS 片选信号

RS (置1为写数据,置0为写命令）

/WR （为0表示写数据) 数据命令区分信号

/RD （为0表示读数据）

RESET 复位LCD（ 用固定命令系列 0 1 0来复位)

数据总线  DATA (8~24位) 

    RGB模式

        大屏采用较多的模式，数据位传输也有6位，16位和18位，24位之分。连线一般有：VSYNC，HSYNC，DOTCLK，CS，RESET，有的也需要RS，剩下就是数据线。它的优缺点正好和MCU模式相反。

    MCU-LCD屏它与RGB-LCD屏主要区别在于显存的位置。RGB-LCD的显存是由系统内存充当的，因此其大小只受限于系统内存的大小，这样RGB-LCD可以做出较大尺寸，象现在4.3"只能算入门级，而MID中7",10"的屏都开始大量使用。而MCU-LCD的设计之初只要考虑单片机的内存较小，因此都是把显存内置在LCD模块内部.然后软件通过专门显示命令来更新显存，因此MCU屏往往不能做得很大。同时显示更新速度也比RGB-LCD慢。显示数据传输模式也有差别。RGB屏只需显存组织好数据。启动显示后，LCD-DMA会自动把显存中的数据通过RGB接口送到LCM。而MCU屏则需要发送画点的命令来修改MCU内部的RAM（即不能直接写MCU屏的RAM）。所以RGB显示速度明显比MCU快，而且播放视频方面，MCU-LCD也比较慢。

    对于RGB接口的LCM，主机输出的直接是每个象素的RGB数据，不需要进行变换（GAMMA校正等除外），对于这种接口，需要在主机部分有个LCD控制器，以产生RGB数据和点、行、帧同步信号。

    MCU接口和RGB接口主要的区别是：

        MCU接口方式：显示数据写入DDRAM，常用于静止图片显示。控制简单方便，无需时钟和同步信号。要耗费GRAM，所以难以做到大屏（QVGA以上）。

        RGB接口方式：显示数据不写入DDRAM，直接写屏，速度快，常用于显示视频或动画用。

    VSYNC模式

        该模式其实就是就是在MCU模式上加了一个VSYNC信号，应用于运动画面更新，这样就与上述两个接口有很大的区别。该模式支持直接进行动画显示的功能，它提供了一个对MCU接口最小的改动，实现动画显示的解决方案。

其他还有 SPI模式  MDDI模式   DSI模式 采用较少 这里不一一介绍。

    显示屏的驱动IC采用Ili93xx 系列的居多，资料较多。我使用的是正点原子的开发板,显示屏驱动IC是xxxB505 ，不过驱动代码和ili9320类似，为i80接口。不过我一直有一个疑问，这块IC的具体位置在哪？ 显示屏由屏幕和排线构成，LCM上只有一块芯片 XPT2046是触摸屏的驱动IC？这样的问题Google也不会知道。。 拆开了一个废旧的显示屏，熟悉了一下显示屏的结构，询问了不少淘宝卖家后，总算弄明白了。这块芯片的封装和常见的芯片不同，以2cm*2mm左右的一块硅片封装在屏幕下和排线相连接。如图：

    这里对正点原子的相关代码进行了整理，使用库函数操作，并且整合和横竖屏的代码，实现横竖屏显示。

相关驱动代码如下:

    LCD/ili93xx.c 

#include "ili93xx.h"#include "font.h"#define USE_HORIZONTAL  0 //定义是否使用横屏//画笔颜色,背景颜色u16 POINT_COLOR = 0x0000,BACK_COLOR = 0xFFFF;  u16 DeviceCode;	 void LCD_Delay_Us(u32 us){    u32 time=100*us/7;        while(--time);   }//LCD延时函数 10MSvoid LCD_Delay (u32 nCount){	volatile int i;	 		for (i=0;i<nCount*100;i++);}//LCD_GPIO_DATA_PIN 模式设置//u8 Mode ://		 	1    推挽输出//			0    上拉输出void LCD_Data_Pin_Mode(u8 Mode){	GPIO_InitTypeDef GPIO_InitStructure;	GPIO_InitStructure.GPIO_Pin = LCD_GPIO_DATA_PIN;	if(Mode == 1)		GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;  	//推挽输出	else		GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU ;		// 上拉输入	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;	GPIO_Init(LCD_GPIO_DATA_PORT, &GPIO_InitStructure);}	//写寄存器函数void LCD_WR_REG(u8 data){ 	Clr_Rs;//写地址  	Clr_Cs; 	Write_Data(data); 	Clr_Wr; 	Set_Wr; 	Set_Cs;  }  //写寄存器void LCD_WriteReg(u8 LCD_Reg, u16 LCD_RegValue){		LCD_WR_REG(LCD_Reg);  	LCD_WR_DATA(LCD_RegValue);	    		 }	   //读寄存器u16 LCD_ReadReg(u8 LCD_Reg){										   	u16 t;	LCD_WR_REG(LCD_Reg);   //写入要读的寄存器号 		LCD_Data_Pin_Mode(0);	//上拉模式		Set_Rs;	Clr_Cs;						  //读取数据(读寄存器时,并不需要读2次)	Clr_Rd;					   	Set_Rd;	t=Read_Data();        	Set_Cs;   		LCD_Data_Pin_Mode(1);	//推挽模式	Write_Data(0xffff);	return t;  }   //开始写GRAMvoid LCD_WriteRAM_Prepare(void){	LCD_WR_REG(R34);}	 //LCD写GRAMvoid LCD_WriteRAM(u16 RGB_Code){							    	LCD_WR_DATA(RGB_Code);//写十六位GRAM}//从ILI93xx读出的数据为GBR格式，而我们写入的时候为RGB格式。//通过该函数转换//c:GBR格式的颜色值//返回值：RGB格式的颜色值u16 LCD_BGR2RGB(u16 c){	u16  r,g,b,rgb;   	b=(c>>0)&0x1f;	g=(c>>5)&0x3f;	r=(c>>11)&0x1f;	 	rgb=(b<<11)+(g<<5)+(r<<0);		 	return(rgb);}			 //读取个某点的颜色值	 //x:0~239//y:0~319//返回值:此点的颜色u16 LCD_ReadPoint(u16 x,u16 y){	u16 t;		if(x>=LCD_WIDTH||y>=LCD_HEIGHT)return 0;//超过了范围,直接返回		   	LCD_SetCursor(x,y);	LCD_WR_REG(R34);       //选择GRAM地址 		LCD_Data_Pin_Mode(0);	//上拉模式	Set_Rs;	Clr_Cs;	//读取数据(读GRAM时,需要读2次)	Clr_Rd;					   	Set_Rd;		LCD_Delay_Us(2);	//dummy READ	Clr_Rd;		LCD_Delay_Us(2);				   	Set_Rd;	t=Read_Data();  	Set_Cs;   	LCD_Data_Pin_Mode(1);	//推挽模式	Write_Data(0xFFFF); 	if(DeviceCode==0X4531||DeviceCode==0X8989||DeviceCode==0XB505)		return t;//4531驱动IC	else 		return LCD_BGR2RGB(t);}//LCD开启显示void LCD_DisplayOn(void){					   	LCD_WriteReg(R7, 0x0173); //26万色显示开启}	 	//LCD关闭显示void LCD_DisplayOff(void){	   	LCD_WriteReg(R7, 0x0);//关闭显示 }    //设置光标位置//Xpos:横坐标//Ypos:纵坐标__inline void LCD_SetCursor(u8 Xpos, u16 Ypos){	#if USE_HORIZONTAL		LCD_WriteReg(R32, Ypos);		LCD_WriteReg(R33, 319-Xpos);	#else		LCD_WriteReg(R32, Xpos);		LCD_WriteReg(R33, Ypos);	#endif} //画点//x:0~239//y:0~319//POINT_COLOR:此点的颜色void LCD_DrawPoint(u16 x,u16 y){	LCD_SetCursor(x,y);//设置光标位置 	LCD_WR_REG(R34);//开始写入GRAM	LCD_WR_DATA(POINT_COLOR); } 	 //初始化lcdvoid LCD_Config(void){ 	/*Set_Cs;	Set_Rs; 	Set_Wr;	Set_Rd;	 */				 	LCD_Delay(5); // LCD_Delay 50 ms 	LCD_WriteReg(0x0000,0x0001);	LCD_Delay(5); // LCD_Delay 50 ms 	DeviceCode = LCD_ReadReg(0x0000);   	//printf("ID:%d\n",DeviceCode);   	if(DeviceCode==0x9325||DeviceCode==0x9328){			//ILI9325				LCD_WriteReg(0x00e7,0x0010);      		LCD_WriteReg(0x0000,0x0001);//开启内部时钟		LCD_WriteReg(0x0001,0x0100);     		LCD_WriteReg(0x0002,0x0700);//电源开启                    		//LCD_WriteReg(0x0003,(1<<3)|(1<<4) ); 	//65K  RGB		//DRIVE TABLE(寄存器 03H)		//BIT3=AM BIT4:5=ID0:1		//AM ID0 ID1   FUNCATION		// 0  0   0	   R->L D->U		// 1  0   0	   D->U	R->L		// 0  1   0	   L->R D->U		// 1  1   0    D->U	L->R		// 0  0   1	   R->L U->D		// 1  0   1    U->D	R->L		// 0  1   1    L->R U->D 正常就用这个.		// 1  1   1	   U->D	L->R		LCD_WriteReg(0x0003,(1<<12)|(3<<4)|(0<<3) );//65K    		LCD_WriteReg(0x0004,0x0000);                                   		LCD_WriteReg(0x0008,0x0207);	           		LCD_WriteReg(0x0009,0x0000);         		LCD_WriteReg(0x000a,0x0000);//display setting         		LCD_WriteReg(0x000c,0x0001);//display setting          		LCD_WriteReg(0x000d,0x0000);//0f3c          		LCD_WriteReg(0x000f,0x0000);		//电源配置		LCD_WriteReg(0x0010,0x0000);   		LCD_WriteReg(0x0011,0x0007);		LCD_WriteReg(0x0012,0x0000);                                                                 		LCD_WriteReg(0x0013,0x0000);                 		LCD_Delay(5); 		LCD_WriteReg(0x0010,0x1590);   		LCD_WriteReg(0x0011,0x0227);		LCD_Delay(5); 		LCD_WriteReg(0x0012,0x009c);                  		LCD_Delay(5); 		LCD_WriteReg(0x0013,0x1900);   		LCD_WriteReg(0x0029,0x0023);		LCD_WriteReg(0x002b,0x000e);		LCD_Delay(5); 		LCD_WriteReg(0x0020,0x0000);                                                            		LCD_WriteReg(0x0021,0x013f);           		LCD_Delay(5); 		//伽马校正		LCD_WriteReg(0x0030,0x0007); 		LCD_WriteReg(0x0031,0x0707);   		LCD_WriteReg(0x0032,0x0006);		LCD_WriteReg(0x0035,0x0704);		LCD_WriteReg(0x0036,0x1f04); 		LCD_WriteReg(0x0037,0x0004);		LCD_WriteReg(0x0038,0x0000);        		LCD_WriteReg(0x0039,0x0706);     		LCD_WriteReg(0x003c,0x0701);		LCD_WriteReg(0x003d,0x000f);		LCD_Delay(5); 		LCD_WriteReg(0x0050,0x0000); //水平GRAM起始位置 		LCD_WriteReg(0x0051,(LCD_WIDTH-1)); //水平GRAM终止位置                    		LCD_WriteReg(0x0052,0x0000); //垂直GRAM起始位置                    		LCD_WriteReg(0x0053,(LCD_HEIGHT-1)); //垂直GRAM终止位置  				LCD_WriteReg(0x0060,0xa700);        		LCD_WriteReg(0x0061,0x0001); 		LCD_WriteReg(0x006a,0x0000);		LCD_WriteReg(0x0080,0x0000);		LCD_WriteReg(0x0081,0x0000);		LCD_WriteReg(0x0082,0x0000);		LCD_WriteReg(0x0083,0x0000);		LCD_WriteReg(0x0084,0x0000);		LCD_WriteReg(0x0085,0x0000);				LCD_WriteReg(0x0090,0x0010);     		LCD_WriteReg(0x0092,0x0000);  		LCD_WriteReg(0x0093,0x0003);		LCD_WriteReg(0x0095,0x0110);		LCD_WriteReg(0x0097,0x0000);        		LCD_WriteReg(0x0098,0x0000);  		//开启显示设置    		LCD_WriteReg(0x0007,0x0133);   		LCD_WriteReg(0x0020,0x0000);                                                            		LCD_WriteReg(0x0021,0x013f);			}else if(DeviceCode==0x9320||DeviceCode==0x9300){				LCD_WriteReg(0x00,0x0000);		LCD_WriteReg(0x01,0x0100);	//Driver Output Contral.		LCD_WriteReg(0x02,0x0700);	//LCD Driver Waveform Contral.		LCD_WriteReg(0x03,0x1030);//Entry Mode Set.		//LCD_WriteReg(0x03,0x1018);	//Entry Mode Set.				LCD_WriteReg(0x04,0x0000);	//Scalling Contral.		LCD_WriteReg(0x08,0x0202);	//Display Contral 2.(0x0207)		LCD_WriteReg(0x09,0x0000);	//Display Contral 3.(0x0000)		LCD_WriteReg(0x0a,0x0000);	//Frame Cycle Contal.(0x0000)		LCD_WriteReg(0x0c,(1<<0));	//Extern Display Interface Contral 1.(0x0000)		LCD_WriteReg(0x0d,0x0000);	//Frame Maker Position.		LCD_WriteReg(0x0f,0x0000);	//Extern Display Interface Contral 2.	    		LCD_Delay(5); 		LCD_WriteReg(0x07,0x0101);	//Display Contral.		LCD_Delay(5); 								  		LCD_WriteReg(0x10,(1<<12)|(0<<8)|(1<<7)|(1<<6)|(0<<4));	//Power Control 1.(0x16b0)		LCD_WriteReg(0x11,0x0007);								//Power Control 2.(0x0001)		LCD_WriteReg(0x12,(1<<8)|(1<<4)|(0<<0));				//Power Control 3.(0x0138)		LCD_WriteReg(0x13,0x0b00);								//Power Control 4.		LCD_WriteReg(0x29,0x0000);								//Power Control 7.				LCD_WriteReg(0x2b,(1<<14)|(1<<4));	    		LCD_WriteReg(0x50,0);	//Set X Star		//水平GRAM终止位置Set X End.		LCD_WriteReg(0x51,(LCD_WIDTH-1));	//Set Y Star		LCD_WriteReg(0x52,0);	//Set Y End.t.		LCD_WriteReg(0x53,(LCD_HEIGHT-1));	//				LCD_WriteReg(0x60,0x2700);	//Driver Output Control.		LCD_WriteReg(0x61,0x0001);	//Driver Output Control.		LCD_WriteReg(0x6a,0x0000);	//Vertical Srcoll Control.				LCD_WriteReg(0x80,0x0000);	//Display Position? Partial Display 1.		LCD_WriteReg(0x81,0x0000);	//RAM Address Start? Partial Display 1.		LCD_WriteReg(0x82,0x0000);	//RAM Address End-Partial Display 1.		LCD_WriteReg(0x83,0x0000);	//Displsy Position? Partial Display 2.		LCD_WriteReg(0x84,0x0000);	//RAM Address Start? Partial Display 2.		LCD_WriteReg(0x85,0x0000);	//RAM Address End? Partial Display 2.				LCD_WriteReg(0x90,(0<<7)|(16<<0));	//Frame Cycle Contral.(0x0013)		LCD_WriteReg(0x92,0x0000);	//Panel Interface Contral 2.(0x0000)		LCD_WriteReg(0x93,0x0001);	//Panel Interface Contral 3.		LCD_WriteReg(0x95,0x0110);	//Frame Cycle Contral.(0x0110)		LCD_WriteReg(0x97,(0<<8));	//		LCD_WriteReg(0x98,0x0000);	//Frame Cycle Contral.	   		LCD_WriteReg(0x07,0x0173);	//(0x0173)						    	}else if(DeviceCode==0x1505){				// second release on 3/5  ,luminance is acceptable,water wave appear during camera preview		LCD_WriteReg(0x0007,0x0000);		LCD_Delay(5); 		LCD_WriteReg(0x0012,0x011C);//0x011A   why need to set several times?		LCD_WriteReg(0x00A4,0x0001);//NVM	 		LCD_WriteReg(0x0008,0x000F);		LCD_WriteReg(0x000A,0x0008);		LCD_WriteReg(0x000D,0x0008);	    		//伽马校正		LCD_WriteReg(0x0030,0x0707);		LCD_WriteReg(0x0031,0x0007); //0x0707		LCD_WriteReg(0x0032,0x0603); 		LCD_WriteReg(0x0033,0x0700); 		LCD_WriteReg(0x0034,0x0202); 		LCD_WriteReg(0x0035,0x0002); //?0x0606		LCD_WriteReg(0x0036,0x1F0F);		LCD_WriteReg(0x0037,0x0707); //0x0f0f  0x0105		LCD_WriteReg(0x0038,0x0000); 		LCD_WriteReg(0x0039,0x0000); 		LCD_WriteReg(0x003A,0x0707); 		LCD_WriteReg(0x003B,0x0000); //0x0303		LCD_WriteReg(0x003C,0x0007); //?0x0707		LCD_WriteReg(0x003D,0x0000); //0x1313//0x1f08		LCD_Delay(5); 		LCD_WriteReg(0x0007,0x0001);		LCD_WriteReg(0x0017,0x0001);//开启电源		LCD_Delay(5); 		//电源配置		LCD_WriteReg(0x0010,0x17A0); 		LCD_WriteReg(0x0011,0x0217);//reference voltage VC[2:0]   Vciout = 1.00*Vcivl		LCD_WriteReg(0x0012,0x011E);//0x011c  //Vreg1out = Vcilvl*1.80   is it the same as Vgama1out ?		LCD_WriteReg(0x0013,0x0F00);//VDV[4:0]-->VCOM Amplitude VcomL = VcomH - Vcom Ampl		LCD_WriteReg(0x002A,0x0000);  		LCD_WriteReg(0x0029,0x000A);//0x0001F  Vcomh = VCM1[4:0]*Vreg1out    gate source voltage??		LCD_WriteReg(0x0012,0x013E);// 0x013C  power supply on		//Coordinates Control//		LCD_WriteReg(0x0050,0x0000);//0x0e00		LCD_WriteReg(0x0051,(LCD_WIDTH-1)); 		LCD_WriteReg(0x0052,0x0000); 		LCD_WriteReg(0x0053,(LCD_HEIGHT-1)); 		//Pannel Image Control//		LCD_WriteReg(0x0060,0x2700); 		LCD_WriteReg(0x0061,0x0001); 		LCD_WriteReg(0x006A,0x0000); 		LCD_WriteReg(0x0080,0x0000); 		//Partial Image Control//		LCD_WriteReg(0x0081,0x0000); 		LCD_WriteReg(0x0082,0x0000); 		LCD_WriteReg(0x0083,0x0000); 		LCD_WriteReg(0x0084,0x0000); 		LCD_WriteReg(0x0085,0x0000); 		//Panel Interface Control//		LCD_WriteReg(0x0090,0x0013);//0x0010 frenqucy		LCD_WriteReg(0x0092,0x0300); 		LCD_WriteReg(0x0093,0x0005); 		LCD_WriteReg(0x0095,0x0000); 		LCD_WriteReg(0x0097,0x0000); 		LCD_WriteReg(0x0098,0x0000); 				LCD_WriteReg(0x0001,0x0100); 		LCD_WriteReg(0x0002,0x0700); 		LCD_WriteReg(0x0003,0x1030); 		LCD_WriteReg(0x0004,0x0000); 		LCD_WriteReg(0x000C,0x0000); 		LCD_WriteReg(0x000F,0x0000); 		LCD_WriteReg(0x0020,0x0000); 		LCD_WriteReg(0x0021,0x0000); 		LCD_WriteReg(0x0007,0x0021); 		LCD_Delay(20);		LCD_WriteReg(0x0007,0x0061); 		LCD_Delay(20);		LCD_WriteReg(0x0007,0x0173); 		LCD_Delay(20);		}else if(DeviceCode==0xB505){					 //stm32 正点原子 LCD 驱动IC			LCD_WriteReg(0x0000,0x0000);		LCD_WriteReg(0x0000,0x0000);		LCD_WriteReg(0x0000,0x0000);		LCD_WriteReg(0x0000,0x0000);				LCD_WriteReg(0x00a4,0x0001);		LCD_Delay(20);		  		LCD_WriteReg(0x0060,0x2700);		LCD_WriteReg(0x0008,0x0202);				LCD_WriteReg(0x0030,0x0214);		LCD_WriteReg(0x0031,0x3715);		LCD_WriteReg(0x0032,0x0604);		LCD_WriteReg(0x0033,0x0e16);		LCD_WriteReg(0x0034,0x2211);		LCD_WriteReg(0x0035,0x1500);		LCD_WriteReg(0x0036,0x8507);		LCD_WriteReg(0x0037,0x1407);		LCD_WriteReg(0x0038,0x1403);		LCD_WriteReg(0x0039,0x0020);				LCD_WriteReg(0x0090,0x001a);		LCD_WriteReg(0x0010,0x0000);		LCD_WriteReg(0x0011,0x0007);		LCD_WriteReg(0x0012,0x0000);		LCD_WriteReg(0x0013,0x0000);		LCD_Delay(20);				LCD_WriteReg(0x0010,0x0730);		LCD_WriteReg(0x0011,0x0137);		LCD_Delay(20);				LCD_WriteReg(0x0012,0x01b8);		LCD_Delay(20);				LCD_WriteReg(0x0013,0x0f00);		LCD_WriteReg(0x002a,0x0080);		LCD_WriteReg(0x0029,0x0048);		LCD_Delay(20);				LCD_WriteReg(0x0001,0x0100);		LCD_WriteReg(0x0002,0x0700);		LCD_WriteReg(0x0003,0x1230);		LCD_WriteReg(0x0008,0x0202);		LCD_WriteReg(0x000a,0x0000);		LCD_WriteReg(0x000c,0x0000);		LCD_WriteReg(0x000d,0x0000);		LCD_WriteReg(0x000e,0x0030);		LCD_WriteReg(0x0050,0x0000);		LCD_WriteReg(0x0051,0x00ef);		LCD_WriteReg(0x0052,0x0000);		LCD_WriteReg(0x0053,0x013f);		LCD_WriteReg(0x0060,0x2700);		LCD_WriteReg(0x0061,0x0001);		LCD_WriteReg(0x006a,0x0000);		//LCD_WriteReg(0x0080,0x0000);		//LCD_WriteReg(0x0081,0x0000);		LCD_WriteReg(0x0090,0X0011);		LCD_WriteReg(0x0092,0x0600);		LCD_WriteReg(0x0093,0x0402);		LCD_WriteReg(0x0094,0x0002);		LCD_Delay(20);				LCD_WriteReg(0x0007,0x0001);		LCD_Delay(20);		LCD_WriteReg(0x0007,0x0061);		LCD_WriteReg(0x0007,0x0173);				LCD_WriteReg(0x0020,0x0000);		LCD_WriteReg(0x0021,0x0000);	  		LCD_WriteReg(0x00,0x22);  								 	}else if(DeviceCode==0x8989){				LCD_WriteReg(0x0000,0x0001);LCD_Delay(5);//打开晶振		LCD_WriteReg(0x0003,0xA8A4);LCD_Delay(5);//0xA8A4		LCD_WriteReg(0x000C,0x0000);LCD_Delay(5);    		LCD_WriteReg(0x000D,0x080C);LCD_Delay(5);    		LCD_WriteReg(0x000E,0x2B00);LCD_Delay(5);    		LCD_WriteReg(0x001E,0x00B0);LCD_Delay(5);    		LCD_WriteReg(0x0001,0x2B3F);LCD_Delay(5);//驱动输出控制320*240  0x6B3F		LCD_WriteReg(0x0002,0x0600);LCD_Delay(5); 		LCD_WriteReg(0x0010,0x0000);LCD_Delay(5); 		LCD_WriteReg(0x0011,0x6070);LCD_Delay(5);//定义数据格式  16位色 		横屏 0x6058		LCD_WriteReg(0x0005,0x0000);LCD_Delay(5); 		LCD_WriteReg(0x0006,0x0000);LCD_Delay(5); 		LCD_WriteReg(0x0016,0xEF1C);LCD_Delay(5); 		LCD_WriteReg(0x0017,0x0003);LCD_Delay(5); 		LCD_WriteReg(0x0007,0x0233);LCD_Delay(5);//0x0233       		LCD_WriteReg(0x000B,0x0000);LCD_Delay(5); 		LCD_WriteReg(0x000F,0x0000);LCD_Delay(5);//扫描开始地址		LCD_WriteReg(0x0041,0x0000);LCD_Delay(5); 		LCD_WriteReg(0x0042,0x0000);LCD_Delay(5); 		LCD_WriteReg(0x0048,0x0000);LCD_Delay(5); 		LCD_WriteReg(0x0049,0x013F);LCD_Delay(5); 		LCD_WriteReg(0x004A,0x0000);LCD_Delay(5); 		LCD_WriteReg(0x004B,0x0000);LCD_Delay(5); 		LCD_WriteReg(0x0044,0xEF00);LCD_Delay(5); 		LCD_WriteReg(0x0045,0x0000);LCD_Delay(5); 		LCD_WriteReg(0x0046,0x013F);LCD_Delay(5); 		LCD_WriteReg(0x0030,0x0707);LCD_Delay(5); 		LCD_WriteReg(0x0031,0x0204);LCD_Delay(5); 		LCD_WriteReg(0x0032,0x0204);LCD_Delay(5); 		LCD_WriteReg(0x0033,0x0502);LCD_Delay(5); 		LCD_WriteReg(0x0034,0x0507);LCD_Delay(5); 		LCD_WriteReg(0x0035,0x0204);LCD_Delay(5); 		LCD_WriteReg(0x0036,0x0204);LCD_Delay(5); 		LCD_WriteReg(0x0037,0x0502);LCD_Delay(5); 		LCD_WriteReg(0x003A,0x0302);LCD_Delay(5); 		LCD_WriteReg(0x003B,0x0302);LCD_Delay(5); 		LCD_WriteReg(0x0023,0x0000);LCD_Delay(5); 		LCD_WriteReg(0x0024,0x0000);LCD_Delay(5); 		LCD_WriteReg(0x0025,0x8000);LCD_Delay(5); 		LCD_WriteReg(0x004f,0);        //行首址0		LCD_WriteReg(0x004e,0);        //列首址0		}else if(DeviceCode==0x4531){			LCD_WriteReg(0X00,0X0001);   		LCD_Delay(50);   		LCD_WriteReg(0X10,0X1628);   		LCD_WriteReg(0X12,0X000e);//0x0006    		LCD_WriteReg(0X13,0X0A39);   		LCD_Delay(10);   		LCD_WriteReg(0X11,0X0040);   		LCD_WriteReg(0X15,0X0050);   		LCD_Delay(40);   		LCD_WriteReg(0X12,0X001e);//16    		LCD_Delay(40);   		LCD_WriteReg(0X10,0X1620);   		LCD_WriteReg(0X13,0X2A39);   		LCD_Delay(10);   		LCD_WriteReg(0X01,0X0100);   		LCD_WriteReg(0X02,0X0300);   		LCD_WriteReg(0X03,0X1030);//改变方向的   		LCD_WriteReg(0X08,0X0202);   		LCD_WriteReg(0X0A,0X0008);   		LCD_WriteReg(0X30,0X0000);   		LCD_WriteReg(0X31,0X0402);   		LCD_WriteReg(0X32,0X0106);   		LCD_WriteReg(0X33,0X0503);   		LCD_WriteReg(0X34,0X0104);   		LCD_WriteReg(0X35,0X0301);   		LCD_WriteReg(0X36,0X0707);   		LCD_WriteReg(0X37,0X0305);   		LCD_WriteReg(0X38,0X0208);   		LCD_WriteReg(0X39,0X0F0B);   		LCD_WriteReg(0X41,0X0002);   		LCD_WriteReg(0X60,0X2700);   		LCD_WriteReg(0X61,0X0001);   		LCD_WriteReg(0X90,0X0210);   		LCD_WriteReg(0X92,0X010A);   		LCD_WriteReg(0X93,0X0004);   		LCD_WriteReg(0XA0,0X0100);   		LCD_WriteReg(0X07,0X0001);   		LCD_WriteReg(0X07,0X0021);   		LCD_WriteReg(0X07,0X0023);   		LCD_WriteReg(0X07,0X0033);   		LCD_WriteReg(0X07,0X0133);   		LCD_WriteReg(0XA0,0X0000); 	}				LCD_Delay(5000);	Set_LED;//点亮背光	 	LCD_Clear(WHITE);}  //清屏函数//Color:要清屏的填充色void LCD_Clear(u16 Color){	u32 index=0;      	LCD_SetCursor(0x00,0x0000);//设置光标位置 	LCD_WriteRAM_Prepare();     //开始写入GRAM	 	  	for(index=0;index<76800;index++)	{		LCD_WR_DATA(Color);   //向每个GRAM写入数据  	}}  	//在指定区域内填充指定颜色//区域大小://  (xend-xsta)*(yend-ysta)void LCD_Fill(u8 xsta,u16 ysta,u8 xend,u16 yend,u16 color){     #if USE_HORIZONTAL 		//横屏	u16 colortemp=POINT_COLOR;	u16 ytemp=ysta;	POINT_COLOR=color;	for(;xsta<=xend;xsta++)	{		for(;ysta<=yend;ysta++)LCD_DrawPoint(xsta,ysta); 		ysta=ytemp;	}  	POINT_COLOR=colortemp; #else	               	 //竖屏	u32 n;	//设置窗口											LCD_WriteReg(R80, xsta); //水平方向GRAM起始地址	LCD_WriteReg(R81, xend); //水平方向GRAM结束地址	LCD_WriteReg(R82, ysta); //垂直方向GRAM起始地址	LCD_WriteReg(R83, yend); //垂直方向GRAM结束地址		LCD_SetCursor(xsta,ysta);//设置光标位置  	LCD_WriteRAM_Prepare();  //开始写入GRAM	 	   	   	n=(u32)(yend-ysta+1)*(xend-xsta+1);    	while(n--){LCD_WR_DATA(color);}//显示所填充的颜色. 	//恢复设置	LCD_WriteReg(R80, 0x0000); //水平方向GRAM起始地址	LCD_WriteReg(R81, (LCD_WIDTH-1)); //水平方向GRAM结束地址	LCD_WriteReg(R82, 0x0000); //垂直方向GRAM起始地址	LCD_WriteReg(R83, (LCD_HEIGHT-1)); //垂直方向GRAM结束地址		    #endif	             }  //画线//x1,y1:起点坐标//x2,y2:终点坐标  void LCD_DrawLine(u16 x1, u16 y1, u16 x2, u16 y2){	u16 t; 	int xerr=0,yerr=0,delta_x,delta_y,distance; 	int incx,incy,uRow,uCol; 		delta_x=x2-x1; //计算坐标增量 	delta_y=y2-y1; 	uRow=x1; 	uCol=y1; 	if(delta_x>0)incx=1; //设置单步方向 	else if(delta_x==0)incx=0;//垂直线 	else {incx=-1;delta_x=-delta_x;}   //终点坐标小于起始坐标,反方向,将坐标重新定位为正坐标	if(delta_y>0)incy=1; 	else if(delta_y==0)incy=0;//水平线 	else{incy=-1;delta_y=-delta_y;}   //终点坐标小于起始坐标,反方向,将坐标重新定位为正坐标	if( delta_x>delta_y)distance=delta_x; //选取基本增量坐标轴 	else distance=delta_y; 	for(t=0;t<=distance+1;t++ )//画线输出 	{  		LCD_DrawPoint(uRow,uCol);//根据坐标画点 		xerr+=delta_x ;  //X坐标增量		yerr+=delta_y ;  //Y坐标增量		if(xerr>distance) 		{ 			xerr-=distance; 			uRow+=incx; 					} 		if(yerr>distance) 		{ 			yerr-=distance; 			uCol+=incy; 		} 	}  }    //画矩形void LCD_DrawRectangle(u8 x1, u16 y1, u8 x2, u16 y2){	LCD_DrawLine(x1,y1,x2,y1);	LCD_DrawLine(x1,y1,x1,y2);	LCD_DrawLine(x1,y2,x2,y2);	LCD_DrawLine(x2,y1,x2,y2);}//在指定位置画一个指定大小的圆//(x,y):中心点//r    :半径void Draw_Circle(u8 x0,u16 y0,u8 r){	int a,b;	int di;	a=0;b=r;	  	di=3-(r<<1);             //判断下个点位置的标志	while(a<=b)	{		LCD_DrawPoint(x0-b,y0-a);             //3           		LCD_DrawPoint(x0+b,y0-a);             //0           		LCD_DrawPoint(x0-a,y0+b);             //1       		LCD_DrawPoint(x0-b,y0-a);             //7           		LCD_DrawPoint(x0-a,y0-b);             //2             		LCD_DrawPoint(x0+b,y0+a);             //4               		LCD_DrawPoint(x0+a,y0-b);             //5		LCD_DrawPoint(x0+a,y0+b);             //6 		LCD_DrawPoint(x0-b,y0+a);             		a++;		//使用Bresenham算法画圆     		if(di<0){			di +=4*a+6;	  		}else{			di+=10+4*(a-b);   			b--;		} 		LCD_DrawPoint(x0+a,y0+b);	}} //在指定位置显示一个字符//x:0~234//y:0~308//num:要显示的字符:" "--->"~"//size:字体大小 12/16//mode:叠加方式(1)还是非叠加方式(0)void LCD_ShowChar(u8 x,u16 y,u8 num,u8 size,u8 mode){       #if USE_HORIZONTAL	#define MAX_CHAR_POSX 312	#define MAX_CHAR_POSY 232 	u8 temp;	u8 pos,t;	u16 x0=x;	u16 colortemp=POINT_COLOR;      	if(x>MAX_CHAR_POSX||y>MAX_CHAR_POSY)return;	    	//设置窗口		   	num=num-' ';//得到偏移后的值	if(!mode) //非叠加方式	{		for(pos=0;pos<size;pos++)		{			if(size==12)				temp=asc2_1206[num][pos];//调用1206字体			else 				temp=asc2_1608[num][pos];		 //调用1608字体			for(t=0;t<size/2;t++)			{                 				if(temp&0x01)					POINT_COLOR=colortemp;				else 					POINT_COLOR=BACK_COLOR;				LCD_DrawPoint(x,y);					temp>>=1; 				x++;			}			x=x0;			y++;		}		}else{											//叠加方式		for(pos=0;pos<size;pos++)		{			if(size==12)				temp=asc2_1206[num][pos];//调用1206字体			else 				temp=asc2_1608[num][pos];		 //调用1608字体			for(t=0;t<size/2;t++)			{                 				if(temp&0x01)LCD_DrawPoint(x+t,y+pos);//画一个点     				temp>>=1; 			}		}	}	POINT_COLOR=colortemp;#else     	#define MAX_CHAR_POSX 232	#define MAX_CHAR_POSY 304 	u8 temp;	u8 pos,t;      	if(x>MAX_CHAR_POSX||y>MAX_CHAR_POSY)return;	    	//设置窗口											LCD_WriteReg(R80,x);           //水平方向GRAM起始地址	LCD_WriteReg(R81,x+(size/2-1));//水平方向GRAM结束地址	LCD_WriteReg(R82,y);           //垂直方向GRAM起始地址	LCD_WriteReg(R83,y+size-1);    //垂直方向GRAM结束地址		LCD_SetCursor(x,y);            //设置光标位置  	LCD_WriteRAM_Prepare();        //开始写入GRAM	   	num=num-' ';//得到偏移后的值	if(!mode) //非叠加方式	{		for(pos=0;pos<size;pos++)		{			if(size==12)					temp=asc2_1206[num][pos];//调用1206字体			else 				temp=asc2_1608[num][pos];		 //调用1608字体			for(t=0;t<size/2;t++)			{                 				if(temp&0x01){					LCD_WR_DATA(POINT_COLOR);				}else{ 					LCD_WR_DATA(BACK_COLOR);				}						        				temp>>=1; 			}		}		}else{			//叠加方式			for(pos=0;pos<size;pos++)		{			if(size==12)				temp=asc2_1206[num][pos];		//调用1206字体			else 				temp=asc2_1608[num][pos];		 //调用1608字体			for(t=0;t<size/2;t++)			{                 				if(temp&0x01)					LCD_DrawPoint(x+t,y+pos);//画一个点     				temp>>=1; 			}		}	}	    	//恢复窗体大小	 	LCD_WriteReg(R80, 0x0000); //水平方向GRAM起始地址	LCD_WriteReg(R81, (LCD_WIDTH-1)); //水平方向GRAM结束地址	LCD_WriteReg(R82, 0x0000); //垂直方向GRAM起始地址	LCD_WriteReg(R83, (LCD_HEIGHT-1)); //垂直方向GRAM结束地址#endif 	   }  //m^n函数u32 mypow(u8 m,u8 n){	u32 result=1;	 	while(n--)result*=m;    	return result;}				 //显示数字//x,y :起点坐标	 //len :数字的位数//size:字体大小//color:颜色//num:数值(0~4294967295);	 void LCD_ShowNum(u8 x,u16 y,u32 num,u8 len,u8 size){         		u8 t,temp;	u8 enshow=0;						   	for(t=0;t<len;t++)	{		temp=(num/mypow(10,len-t-1))%10;		if(enshow==0&&t<(len-1))		{			if(temp==0)			{				LCD_ShowChar(x+(size/2)*t,y,' ',size,0);				continue;			}else{ 				enshow=1; 			}		}		LCD_ShowChar(x+(size/2)*t,y,temp+'0',size,0); 	}} //显示字符串//x,y:起点坐标  //*p:字符串起始地址//用16字体void LCD_ShowString(u8 x,u16 y,const u8 *p){         	while(*p!='\0')	 //字符串到达结束	{       		if(x>MAX_CHAR_POSX){x=0;y+=16;}	   //换行		if(y>MAX_CHAR_POSY){y=x=0;LCD_Clear(WHITE);}  //超出屏幕显示范围		LCD_ShowChar(x,y,*p,16,0);		x+=8;		p++;	}  }

    LCD/ili93xx.h (相关I/O操作在此文件中以宏定义的方式实现)

#include "stm32f10x.h"	//TFTLCD部分外要调用的函数		   extern u16  POINT_COLOR;//默认红色    extern u16  BACK_COLOR; //背景颜色.默认为白色//定义LCD的尺寸#define LCD_WIDTH 240#define LCD_HEIGHT 320//9320/9325 LCD寄存器  #define R0             0x00#define R1             0x01#define R2             0x02#define R3             0x03#define R4             0x04#define R5             0x05#define R6             0x06#define R7             0x07#define R8             0x08#define R9             0x09#define R10            0x0A#define R12            0x0C#define R13            0x0D#define R14            0x0E#define R15            0x0F#define R16            0x10#define R17            0x11#define R18            0x12#define R19            0x13#define R20            0x14#define R21            0x15#define R22            0x16#define R23            0x17#define R24            0x18#define R25            0x19#define R26            0x1A#define R27            0x1B#define R28            0x1C#define R29            0x1D#define R30            0x1E#define R31            0x1F#define R32            0x20#define R33            0x21#define R34            0x22#define R36            0x24#define R37            0x25#define R40            0x28#define R41            0x29#define R43            0x2B#define R45            0x2D#define R48            0x30#define R49            0x31#define R50            0x32#define R51            0x33#define R52            0x34#define R53            0x35#define R54            0x36#define R55            0x37#define R56            0x38#define R57            0x39#define R59            0x3B#define R60            0x3C#define R61            0x3D#define R62            0x3E#define R63            0x3F#define R64            0x40#define R65            0x41#define R66            0x42#define R67            0x43#define R68            0x44#define R69            0x45#define R70            0x46#define R71            0x47#define R72            0x48#define R73            0x49#define R74            0x4A#define R75            0x4B#define R76            0x4C#define R77            0x4D#define R78            0x4E#define R79            0x4F#define R80            0x50#define R81            0x51#define R82            0x52#define R83            0x53#define R96            0x60#define R97            0x61#define R106           0x6A#define R118           0x76#define R128           0x80#define R129           0x81#define R130           0x82#define R131           0x83#define R132           0x84#define R133           0x85#define R134           0x86#define R135           0x87#define R136           0x88#define R137           0x89#define R139           0x8B#define R140           0x8C#define R141           0x8D#define R143           0x8F#define R144           0x90#define R145           0x91#define R146           0x92#define R147           0x93#define R148           0x94#define R149           0x95#define R150           0x96#define R151           0x97#define R152           0x98#define R153           0x99#define R154           0x9A#define R157           0x9D#define R192           0xC0#define R193           0xC1#define R229           0xE5/*硬件相关的宏定义*/#define LCD_FAST_IO     1 	//定义是否使用快速IO	 建议使用快速IO,效率更高//-----------------LCD端口定义---------------- /********************************************************************************/#define LCD_GPIO_LED_PORT              GPIOC#define LCD_GPIO_LED_PIN               GPIO_Pin_10#define LCD_GPIO_CS_PORT              GPIOC#define LCD_GPIO_CS_PIN               GPIO_Pin_9#define LCD_GPIO_RS_PORT              GPIOC#define LCD_GPIO_RS_PIN               GPIO_Pin_8#define LCD_GPIO_WR_PORT             GPIOC #define LCD_GPIO_WR_PIN              GPIO_Pin_7#define LCD_GPIO_RD_PORT              GPIOC #define LCD_GPIO_RD_PIN               GPIO_Pin_6//16位数据所在端口,PB0~15作为数据线 #define LCD_GPIO_DATA_PORT            GPIOB#define LCD_GPIO_DATA_PIN             GPIO_Pin_All   #if LCD_FAST_IO == 1 //快速IO#define	Set_Cs  GPIOC->BSRR=1<<9    //片选端口  	     PC9#define	Set_Rs	GPIOC->BSRR=1<<8    //数据/命令          PC8	   #define	Set_Wr	GPIOC->BSRR=1<<7    //写数据			 PC7#define	Set_Rd	GPIOC->BSRR=1<<6    //读数据			 PC6								    #define	Clr_Cs  GPIOC->BRR=1<<9     //片选端口  	     PC9#define	Clr_Rs	GPIOC->BRR=1<<8     //数据/命令          PC8	   #define	Clr_Wr	GPIOC->BRR=1<<7     //写数据			 PC7#define	Clr_Rd	GPIOC->BRR=1<<6     //读数据			 PC6#else#define Set_Cs   {GPIO_SetBits(LCD_GPIO_CS_PORT,LCD_GPIO_CS_PIN);}#define Clr_Cs   {GPIO_ResetBits(LCD_GPIO_CS_PORT,LCD_GPIO_CS_PIN);}#define Set_Rs   {GPIO_SetBits(LCD_GPIO_RS_PORT,LCD_GPIO_RS_PIN);}#define Clr_Rs   {GPIO_ResetBits(LCD_GPIO_RS_PORT,LCD_GPIO_RS_PIN);}#define Set_Wr   {GPIO_SetBits(LCD_GPIO_WR_PORT,LCD_GPIO_WR_PIN);}#define Clr_Wr   {GPIO_ResetBits(LCD_GPIO_WR_PORT,LCD_GPIO_WR_PIN);}#define Set_Rd   {GPIO_SetBits(LCD_GPIO_RD_PORT,LCD_GPIO_RD_PIN);}#define Clr_Rd   {GPIO_ResetBits(LCD_GPIO_RD_PORT,LCD_GPIO_RD_PIN);}#endif#define Set_LED  {GPIO_SetBits(LCD_GPIO_LED_PORT,LCD_GPIO_LED_PIN);}#define Clr_LED  {GPIO_ResetBits(LCD_GPIO_LED_PORT,LCD_GPIO_LED_PIN);} #define Write_Data(DataValue) {GPIO_Write(LCD_GPIO_DATA_PORT,DataValue);}//直接操作寄存器读取,使用库函数读取I/O有问题,原因不详#define Read_Data() (LCD_GPIO_DATA_PORT ->IDR)						//必须使用宏定义,写成函数会有问题//#define Read_Data()  (GPIO_ReadInputData(LCD_GPIO_DATA_PORT))	    //这句有问题//写8位数据函数//用宏定义,提高速度.#define  LCD_WR_DATA(data){Set_Rs;Clr_Cs;Write_Data(data);Clr_Wr;Set_Wr;Set_Cs;} /********************************************************************************/								      //画笔颜色#define WHITE         	 0xFFFF#define BLACK         	 0x0000	  #define BLUE         	 0x001F  #define BRED             0XF81F#define GRED 			 0XFFE0#define GBLUE			 0X07FF#define RED           	 0xF800#define MAGENTA       	 0xF81F#define GREEN         	 0x07E0#define CYAN          	 0x7FFF#define YELLOW        	 0xFFE0#define BROWN 			 0XBC40 //棕色#define BRRED 			 0XFC07 //棕红色#define GRAY  			 0X8430 //灰色//GUI颜色#define DARKBLUE      	 0X01CF	//深蓝色#define LIGHTBLUE      	 0X7D7C	//浅蓝色  #define GRAYBLUE       	 0X5458 //灰蓝色//以上三色为PANEL的颜色  #define LIGHTGREEN     	 0X841F //浅绿色//#define LIGHTGRAY        0XEF5B //浅灰色(PANNEL)#define LGRAY 			 0XC618 //浅灰色(PANNEL),窗体背景色#define LGRAYBLUE        0XA651 //浅灰蓝色(中间层颜色)#define LBBLUE           0X2B12 //浅棕蓝色(选择条目的反色)void LCD_Delay(u32 nCount);void LCD_Config(void);void LCD_DisplayOn(void);void LCD_DisplayOff(void);void LCD_Clear(u16 Color);	 void LCD_SetCursor(u8 Xpos, u16 Ypos);void LCD_DrawPoint(u16 x,u16 y);//画点u16 LCD_ReadPoint(u16 x,u16 y); //读点void Draw_Circle(u8 x0,u16 y0,u8 r);void LCD_DrawLine(u16 x1, u16 y1, u16 x2, u16 y2);void LCD_DrawRectangle(u8 x1, u16 y1, u8 x2, u16 y2);		   void LCD_Fill(u8 xsta,u16 ysta,u8 xend,u16 yend,u16 color);void LCD_ShowChar(u8 x,u16 y,u8 num,u8 size,u8 mode);//显示一个字符void LCD_ShowNum(u8 x,u16 y,u32 num,u8 len,u8 size);  //显示一个数字void LCD_ShowString(u8 x,u16 y,const u8 *p);		 //显示一个字符串,16字体void LCD_WriteReg(u8 LCD_Reg, u16 LCD_RegValue);u16 LCD_ReadReg(u8 LCD_Reg);void LCD_WriteRAM_Prepare(void);void LCD_WriteRAM(u16 RGB_Code);u16 LCD_ReadRAM(void);		   

 font.h （字库文件）

   //常用ASCII表//偏移量32//ASCII字符集//偏移量32//大小:12*6const unsigned char asc2_1206[95][12]={{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/{0x00,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x00,0x04,0x00,0x00},/*"!",1*/{0x00,0x14,0x0A,0x0A,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*""",2*/{0x00,0x00,0x14,0x14,0x3F,0x14,0x0A,0x3F,0x0A,0x0A,0x00,0x00},/*"#",3*/{0x00,0x04,0x1E,0x15,0x05,0x06,0x0C,0x14,0x15,0x0F,0x04,0x00},/*"$",4*/{0x00,0x00,0x12,0x15,0x0D,0x0A,0x14,0x2C,0x2A,0x12,0x00,0x00},/*"%",5*/{0x00,0x00,0x04,0x0A,0x0A,0x1E,0x15,0x15,0x09,0x36,0x00,0x00},/*"&",6*/{0x00,0x02,0x02,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/{0x00,0x20,0x10,0x08,0x08,0x08,0x08,0x08,0x08,0x10,0x20,0x00},/*"(",8*/{0x00,0x02,0x04,0x08,0x08,0x08,0x08,0x08,0x08,0x04,0x02,0x00},/*")",9*/{0x00,0x00,0x00,0x04,0x15,0x0E,0x0E,0x15,0x04,0x00,0x00,0x00},/*"*",10*/{0x00,0x00,0x04,0x04,0x04,0x1F,0x04,0x04,0x04,0x00,0x00,0x00},/*"+",11*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x02,0x02,0x01},/*",",12*/{0x00,0x00,0x00,0x00,0x00,0x1F,0x00,0x00,0x00,0x00,0x00,0x00},/*"-",13*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x02,0x00,0x00},/*".",14*/{0x00,0x10,0x08,0x08,0x08,0x04,0x04,0x02,0x02,0x02,0x01,0x00},/*"/",15*/{0x00,0x00,0x0E,0x11,0x11,0x11,0x11,0x11,0x11,0x0E,0x00,0x00},/*"0",16*/{0x00,0x00,0x04,0x06,0x04,0x04,0x04,0x04,0x04,0x0E,0x00,0x00},/*"1",17*/{0x00,0x00,0x0E,0x11,0x11,0x08,0x04,0x02,0x01,0x1F,0x00,0x00},/*"2",18*/{0x00,0x00,0x0E,0x11,0x10,0x0C,0x10,0x10,0x11,0x0E,0x00,0x00},/*"3",19*/{0x00,0x00,0x08,0x0C,0x0A,0x0A,0x09,0x1E,0x08,0x18,0x00,0x00},/*"4",20*/{0x00,0x00,0x1F,0x01,0x01,0x0F,0x10,0x10,0x11,0x0E,0x00,0x00},/*"5",21*/{0x00,0x00,0x0E,0x09,0x01,0x0F,0x11,0x11,0x11,0x0E,0x00,0x00},/*"6",22*/{0x00,0x00,0x1F,0x09,0x08,0x04,0x04,0x04,0x04,0x04,0x00,0x00},/*"7",23*/{0x00,0x00,0x0E,0x11,0x11,0x0E,0x11,0x11,0x11,0x0E,0x00,0x00},/*"8",24*/{0x00,0x00,0x0E,0x11,0x11,0x11,0x1E,0x10,0x12,0x0E,0x00,0x00},/*"9",25*/{0x00,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x00,0x04,0x00,0x00},/*":",26*/{0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x04,0x00},/*";",27*/{0x00,0x20,0x10,0x08,0x04,0x02,0x04,0x08,0x10,0x20,0x00,0x00},/*"<",28*/{0x00,0x00,0x00,0x00,0x1F,0x00,0x00,0x1F,0x00,0x00,0x00,0x00},/*"=",29*/{0x00,0x02,0x04,0x08,0x10,0x20,0x10,0x08,0x04,0x02,0x00,0x00},/*">",30*/{0x00,0x00,0x0E,0x11,0x11,0x08,0x04,0x04,0x00,0x04,0x00,0x00},/*"?",31*/{0x00,0x00,0x0E,0x11,0x19,0x15,0x15,0x1D,0x01,0x1E,0x00,0x00},/*"@",32*/{0x00,0x00,0x04,0x04,0x0C,0x0A,0x0A,0x1E,0x12,0x33,0x00,0x00},/*"A",33*/{0x00,0x00,0x0F,0x12,0x12,0x0E,0x12,0x12,0x12,0x0F,0x00,0x00},/*"B",34*/{0x00,0x00,0x1E,0x11,0x01,0x01,0x01,0x01,0x11,0x0E,0x00,0x00},/*"C",35*/{0x00,0x00,0x0F,0x12,0x12,0x12,0x12,0x12,0x12,0x0F,0x00,0x00},/*"D",36*/{0x00,0x00,0x1F,0x12,0x0A,0x0E,0x0A,0x02,0x12,0x1F,0x00,0x00},/*"E",37*/{0x00,0x00,0x1F,0x12,0x0A,0x0E,0x0A,0x02,0x02,0x07,0x00,0x00},/*"F",38*/{0x00,0x00,0x1C,0x12,0x01,0x01,0x39,0x11,0x12,0x0C,0x00,0x00},/*"G",39*/{0x00,0x00,0x33,0x12,0x12,0x1E,0x12,0x12,0x12,0x33,0x00,0x00},/*"H",40*/{0x00,0x00,0x1F,0x04,0x04,0x04,0x04,0x04,0x04,0x1F,0x00,0x00},/*"I",41*/{0x00,0x00,0x3E,0x08,0x08,0x08,0x08,0x08,0x08,0x09,0x07,0x00},/*"J",42*/{0x00,0x00,0x37,0x12,0x0A,0x06,0x0A,0x0A,0x12,0x37,0x00,0x00},/*"K",43*/{0x00,0x00,0x07,0x02,0x02,0x02,0x02,0x02,0x22,0x3F,0x00,0x00},/*"L",44*/{0x00,0x00,0x1B,0x1B,0x1B,0x1B,0x15,0x15,0x15,0x15,0x00,0x00},/*"M",45*/{0x00,0x00,0x3B,0x12,0x16,0x16,0x1A,0x1A,0x12,0x17,0x00,0x00},/*"N",46*/{0x00,0x00,0x0E,0x11,0x11,0x11,0x11,0x11,0x11,0x0E,0x00,0x00},/*"O",47*/{0x00,0x00,0x0F,0x12,0x12,0x0E,0x02,0x02,0x02,0x07,0x00,0x00},/*"P",48*/{0x00,0x00,0x0E,0x11,0x11,0x11,0x11,0x17,0x19,0x0E,0x18,0x00},/*"Q",49*/{0x00,0x00,0x0F,0x12,0x12,0x0E,0x0A,0x12,0x12,0x37,0x00,0x00},/*"R",50*/{0x00,0x00,0x1E,0x11,0x01,0x06,0x08,0x10,0x11,0x0F,0x00,0x00},/*"S",51*/{0x00,0x00,0x1F,0x15,0x04,0x04,0x04,0x04,0x04,0x0E,0x00,0x00},/*"T",52*/{0x00,0x00,0x33,0x12,0x12,0x12,0x12,0x12,0x12,0x0C,0x00,0x00},/*"U",53*/{0x00,0x00,0x33,0x12,0x12,0x0A,0x0A,0x0C,0x04,0x04,0x00,0x00},/*"V",54*/{0x00,0x00,0x15,0x15,0x15,0x0E,0x0A,0x0A,0x0A,0x0A,0x00,0x00},/*"W",55*/{0x00,0x00,0x1B,0x0A,0x0A,0x04,0x04,0x0A,0x0A,0x1B,0x00,0x00},/*"X",56*/{0x00,0x00,0x1B,0x0A,0x0A,0x04,0x04,0x04,0x04,0x0E,0x00,0x00},/*"Y",57*/{0x00,0x00,0x1F,0x09,0x08,0x04,0x04,0x02,0x12,0x1F,0x00,0x00},/*"Z",58*/{0x00,0x1C,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x1C,0x00},/*"[",59*/{0x00,0x02,0x02,0x02,0x04,0x04,0x08,0x08,0x08,0x10,0x00,0x00},/*"\",60*/{0x00,0x0E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x0E,0x00},/*"]",61*/{0x00,0x04,0x0A,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"^",62*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F},/*"_",63*/{0x00,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/{0x00,0x00,0x00,0x00,0x00,0x0C,0x12,0x1C,0x12,0x3C,0x00,0x00},/*"a",65*/{0x00,0x00,0x03,0x02,0x02,0x0E,0x12,0x12,0x12,0x0E,0x00,0x00},/*"b",66*/{0x00,0x00,0x00,0x00,0x00,0x1C,0x12,0x02,0x02,0x1C,0x00,0x00},/*"c",67*/{0x00,0x00,0x18,0x10,0x10,0x1C,0x12,0x12,0x12,0x3C,0x00,0x00},/*"d",68*/{0x00,0x00,0x00,0x00,0x00,0x0C,0x12,0x1E,0x02,0x1C,0x00,0x00},/*"e",69*/{0x00,0x00,0x38,0x04,0x04,0x1E,0x04,0x04,0x04,0x1E,0x00,0x00},/*"f",70*/{0x00,0x00,0x00,0x00,0x00,0x3C,0x12,0x0C,0x02,0x1E,0x22,0x1C},/*"g",71*/{0x00,0x00,0x03,0x02,0x02,0x0E,0x12,0x12,0x12,0x37,0x00,0x00},/*"h",72*/{0x00,0x00,0x04,0x00,0x00,0x06,0x04,0x04,0x04,0x0E,0x00,0x00},/*"i",73*/{0x00,0x00,0x08,0x00,0x00,0x0C,0x08,0x08,0x08,0x08,0x08,0x07},/*"j",74*/{0x00,0x00,0x03,0x02,0x02,0x3A,0x0A,0x0E,0x12,0x37,0x00,0x00},/*"k",75*/{0x00,0x00,0x07,0x04,0x04,0x04,0x04,0x04,0x04,0x1F,0x00,0x00},/*"l",76*/{0x00,0x00,0x00,0x00,0x00,0x0F,0x15,0x15,0x15,0x15,0x00,0x00},/*"m",77*/{0x00,0x00,0x00,0x00,0x00,0x0F,0x12,0x12,0x12,0x37,0x00,0x00},/*"n",78*/{0x00,0x00,0x00,0x00,0x00,0x0C,0x12,0x12,0x12,0x0C,0x00,0x00},/*"o",79*/{0x00,0x00,0x00,0x00,0x00,0x0F,0x12,0x12,0x12,0x0E,0x02,0x07},/*"p",80*/{0x00,0x00,0x00,0x00,0x00,0x1C,0x12,0x12,0x12,0x1C,0x10,0x38},/*"q",81*/{0x00,0x00,0x00,0x00,0x00,0x1B,0x06,0x02,0x02,0x07,0x00,0x00},/*"r",82*/{0x00,0x00,0x00,0x00,0x00,0x1E,0x02,0x0C,0x10,0x1E,0x00,0x00},/*"s",83*/{0x00,0x00,0x00,0x04,0x04,0x0E,0x04,0x04,0x04,0x18,0x00,0x00},/*"t",84*/{0x00,0x00,0x00,0x00,0x00,0x1B,0x12,0x12,0x12,0x3C,0x00,0x00},/*"u",85*/{0x00,0x00,0x00,0x00,0x00,0x37,0x12,0x0A,0x0C,0x04,0x00,0x00},/*"v",86*/{0x00,0x00,0x00,0x00,0x00,0x15,0x15,0x0E,0x0A,0x0A,0x00,0x00},/*"w",87*/{0x00,0x00,0x00,0x00,0x00,0x1B,0x0A,0x04,0x0A,0x1B,0x00,0x00},/*"x",88*/{0x00,0x00,0x00,0x00,0x00,0x37,0x12,0x0A,0x0C,0x04,0x04,0x03},/*"y",89*/{0x00,0x00,0x00,0x00,0x00,0x1E,0x08,0x04,0x04,0x1E,0x00,0x00},/*"z",90*/{0x00,0x18,0x08,0x08,0x08,0x04,0x08,0x08,0x08,0x08,0x18,0x00},/*"{",91*/{0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08},/*"|",92*/{0x00,0x06,0x04,0x04,0x04,0x08,0x04,0x04,0x04,0x04,0x06,0x00},/*"}",93*/{0x02,0x25,0x18,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00} /*"~",94*/}; const unsigned char asc2_1608[95][16]={{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/{0x00,0x00,0x00,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x00,0x00,0x18,0x18,0x00,0x00},/*"!",1*/{0x00,0x48,0x6C,0x24,0x12,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*""",2*/{0x00,0x00,0x00,0x24,0x24,0x24,0x7F,0x12,0x12,0x12,0x7F,0x12,0x12,0x12,0x00,0x00},/*"#",3*/{0x00,0x00,0x08,0x1C,0x2A,0x2A,0x0A,0x0C,0x18,0x28,0x28,0x2A,0x2A,0x1C,0x08,0x08},/*"$",4*/{0x00,0x00,0x00,0x22,0x25,0x15,0x15,0x15,0x2A,0x58,0x54,0x54,0x54,0x22,0x00,0x00},/*"%",5*/{0x00,0x00,0x00,0x0C,0x12,0x12,0x12,0x0A,0x76,0x25,0x29,0x11,0x91,0x6E,0x00,0x00},/*"&",6*/{0x00,0x06,0x06,0x04,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/{0x00,0x40,0x20,0x10,0x10,0x08,0x08,0x08,0x08,0x08,0x08,0x10,0x10,0x20,0x40,0x00},/*"(",8*/{0x00,0x02,0x04,0x08,0x08,0x10,0x10,0x10,0x10,0x10,0x10,0x08,0x08,0x04,0x02,0x00},/*")",9*/{0x00,0x00,0x00,0x00,0x08,0x08,0x6B,0x1C,0x1C,0x6B,0x08,0x08,0x00,0x00,0x00,0x00},/*"*",10*/{0x00,0x00,0x00,0x00,0x08,0x08,0x08,0x08,0x7F,0x08,0x08,0x08,0x08,0x00,0x00,0x00},/*"+",11*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0x04,0x03},/*",",12*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"-",13*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0x00,0x00},/*".",14*/{0x00,0x00,0x80,0x40,0x40,0x20,0x20,0x10,0x10,0x08,0x08,0x04,0x04,0x02,0x02,0x00},/*"/",15*/{0x00,0x00,0x00,0x18,0x24,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x24,0x18,0x00,0x00},/*"0",16*/{0x00,0x00,0x00,0x08,0x0E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"1",17*/{0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x20,0x20,0x10,0x08,0x04,0x42,0x7E,0x00,0x00},/*"2",18*/{0x00,0x00,0x00,0x3C,0x42,0x42,0x20,0x18,0x20,0x40,0x40,0x42,0x22,0x1C,0x00,0x00},/*"3",19*/{0x00,0x00,0x00,0x20,0x30,0x28,0x24,0x24,0x22,0x22,0x7E,0x20,0x20,0x78,0x00,0x00},/*"4",20*/{0x00,0x00,0x00,0x7E,0x02,0x02,0x02,0x1A,0x26,0x40,0x40,0x42,0x22,0x1C,0x00,0x00},/*"5",21*/{0x00,0x00,0x00,0x38,0x24,0x02,0x02,0x1A,0x26,0x42,0x42,0x42,0x24,0x18,0x00,0x00},/*"6",22*/{0x00,0x00,0x00,0x7E,0x22,0x22,0x10,0x10,0x08,0x08,0x08,0x08,0x08,0x08,0x00,0x00},/*"7",23*/	 {0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x24,0x18,0x24,0x42,0x42,0x42,0x3C,0x00,0x00},/*"8",24*/{0x00,0x00,0x00,0x18,0x24,0x42,0x42,0x42,0x64,0x58,0x40,0x40,0x24,0x1C,0x00,0x00},/*"9",25*/{0x00,0x00,0x00,0x00,0x00,0x00,0x18,0x18,0x00,0x00,0x00,0x00,0x18,0x18,0x00,0x00},/*":",26*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x08,0x08,0x04},/*";",27*/{0x00,0x00,0x00,0x40,0x20,0x10,0x08,0x04,0x02,0x04,0x08,0x10,0x20,0x40,0x00,0x00},/*"<",28*/{0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x00,0x00,0x00,0x7F,0x00,0x00,0x00,0x00,0x00},/*"=",29*/{0x00,0x00,0x00,0x02,0x04,0x08,0x10,0x20,0x40,0x20,0x10,0x08,0x04,0x02,0x00,0x00},/*">",30*/{0x00,0x00,0x00,0x3C,0x42,0x42,0x46,0x40,0x20,0x10,0x10,0x00,0x18,0x18,0x00,0x00},/*"?",31*/{0x00,0x00,0x00,0x1C,0x22,0x5A,0x55,0x55,0x55,0x55,0x2D,0x42,0x22,0x1C,0x00,0x00},/*"@",32*/{0x00,0x00,0x00,0x08,0x08,0x18,0x14,0x14,0x24,0x3C,0x22,0x42,0x42,0xE7,0x00,0x00},/*"A",33*/{0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x1E,0x22,0x42,0x42,0x42,0x22,0x1F,0x00,0x00},/*"B",34*/{0x00,0x00,0x00,0x7C,0x42,0x42,0x01,0x01,0x01,0x01,0x01,0x42,0x22,0x1C,0x00,0x00},/*"C",35*/{0x00,0x00,0x00,0x1F,0x22,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x22,0x1F,0x00,0x00},/*"D",36*/{0x00,0x00,0x00,0x3F,0x42,0x12,0x12,0x1E,0x12,0x12,0x02,0x42,0x42,0x3F,0x00,0x00},/*"E",37*/{0x00,0x00,0x00,0x3F,0x42,0x12,0x12,0x1E,0x12,0x12,0x02,0x02,0x02,0x07,0x00,0x00},/*"F",38*/{0x00,0x00,0x00,0x3C,0x22,0x22,0x01,0x01,0x01,0x71,0x21,0x22,0x22,0x1C,0x00,0x00},/*"G",39*/{0x00,0x00,0x00,0xE7,0x42,0x42,0x42,0x42,0x7E,0x42,0x42,0x42,0x42,0xE7,0x00,0x00},/*"H",40*/{0x00,0x00,0x00,0x3E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"I",41*/{0x00,0x00,0x00,0x7C,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x11,0x0F},/*"J",42*/{0x00,0x00,0x00,0x77,0x22,0x12,0x0A,0x0E,0x0A,0x12,0x12,0x22,0x22,0x77,0x00,0x00},/*"K",43*/{0x00,0x00,0x00,0x07,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x42,0x7F,0x00,0x00},/*"L",44*/{0x00,0x00,0x00,0x77,0x36,0x36,0x36,0x36,0x2A,0x2A,0x2A,0x2A,0x2A,0x6B,0x00,0x00},/*"M",45*/{0x00,0x00,0x00,0xE3,0x46,0x46,0x4A,0x4A,0x52,0x52,0x52,0x62,0x62,0x47,0x00,0x00},/*"N",46*/{0x00,0x00,0x00,0x1C,0x22,0x41,0x41,0x41,0x41,0x41,0x41,0x41,0x22,0x1C,0x00,0x00},/*"O",47*/{0x00,0x00,0x00,0x3F,0x42,0x42,0x42,0x42,0x3E,0x02,0x02,0x02,0x02,0x07,0x00,0x00},/*"P",48*/{0x00,0x00,0x00,0x1C,0x22,0x41,0x41,0x41,0x41,0x41,0x4D,0x53,0x32,0x1C,0x60,0x00},/*"Q",49*/{0x00,0x00,0x00,0x3F,0x42,0x42,0x42,0x3E,0x12,0x12,0x22,0x22,0x42,0xC7,0x00,0x00},/*"R",50*/{0x00,0x00,0x00,0x7C,0x42,0x42,0x02,0x04,0x18,0x20,0x40,0x42,0x42,0x3E,0x00,0x00},/*"S",51*/{0x00,0x00,0x00,0x7F,0x49,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x1C,0x00,0x00},/*"T",52*/{0x00,0x00,0x00,0xE7,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x3C,0x00,0x00},/*"U",53*/{0x00,0x00,0x00,0xE7,0x42,0x42,0x22,0x24,0x24,0x14,0x14,0x18,0x08,0x08,0x00,0x00},/*"V",54*/{0x00,0x00,0x00,0x6B,0x49,0x49,0x49,0x49,0x55,0x55,0x36,0x22,0x22,0x22,0x00,0x00},/*"W",55*/{0x00,0x00,0x00,0xE7,0x42,0x24,0x24,0x18,0x18,0x18,0x24,0x24,0x42,0xE7,0x00,0x00},/*"X",56*/{0x00,0x00,0x00,0x77,0x22,0x22,0x14,0x14,0x08,0x08,0x08,0x08,0x08,0x1C,0x00,0x00},/*"Y",57*/{0x00,0x00,0x00,0x7E,0x21,0x20,0x10,0x10,0x08,0x04,0x04,0x42,0x42,0x3F,0x00,0x00},/*"Z",58*/{0x00,0x78,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x78,0x00},/*"[",59*/{0x00,0x00,0x02,0x02,0x04,0x04,0x08,0x08,0x08,0x10,0x10,0x20,0x20,0x20,0x40,0x40},/*"\",60*/{0x00,0x1E,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x1E,0x00},/*"]",61*/{0x00,0x38,0x44,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"^",62*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF},/*"_",63*/{0x00,0x06,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x42,0x78,0x44,0x42,0x42,0xFC,0x00,0x00},/*"a",65*/{0x00,0x00,0x00,0x03,0x02,0x02,0x02,0x1A,0x26,0x42,0x42,0x42,0x26,0x1A,0x00,0x00},/*"b",66*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x38,0x44,0x02,0x02,0x02,0x44,0x38,0x00,0x00},/*"c",67*/{0x00,0x00,0x00,0x60,0x40,0x40,0x40,0x78,0x44,0x42,0x42,0x42,0x64,0xD8,0x00,0x00},/*"d",68*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x42,0x7E,0x02,0x02,0x42,0x3C,0x00,0x00},/*"e",69*/{0x00,0x00,0x00,0xF0,0x88,0x08,0x08,0x7E,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"f",70*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7C,0x22,0x22,0x1C,0x02,0x3C,0x42,0x42,0x3C},/*"g",71*/{0x00,0x00,0x00,0x03,0x02,0x02,0x02,0x3A,0x46,0x42,0x42,0x42,0x42,0xE7,0x00,0x00},/*"h",72*/{0x00,0x00,0x00,0x0C,0x0C,0x00,0x00,0x0E,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"i",73*/{0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x38,0x20,0x20,0x20,0x20,0x20,0x20,0x22,0x1E},/*"j",74*/{0x00,0x00,0x00,0x03,0x02,0x02,0x02,0x72,0x12,0x0A,0x16,0x12,0x22,0x77,0x00,0x00},/*"k",75*/{0x00,0x00,0x00,0x0E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"l",76*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x92,0x92,0x92,0x92,0x92,0xB7,0x00,0x00},/*"m",77*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3B,0x46,0x42,0x42,0x42,0x42,0xE7,0x00,0x00},/*"n",78*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x42,0x42,0x3C,0x00,0x00},/*"o",79*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1B,0x26,0x42,0x42,0x42,0x22,0x1E,0x02,0x07},/*"p",80*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x78,0x44,0x42,0x42,0x42,0x44,0x78,0x40,0xE0},/*"q",81*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x77,0x4C,0x04,0x04,0x04,0x04,0x1F,0x00,0x00},/*"r",82*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7C,0x42,0x02,0x3C,0x40,0x42,0x3E,0x00,0x00},/*"s",83*/{0x00,0x00,0x00,0x00,0x00,0x08,0x08,0x3E,0x08,0x08,0x08,0x08,0x08,0x30,0x00,0x00},/*"t",84*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x63,0x42,0x42,0x42,0x42,0x62,0xDC,0x00,0x00},/*"u",85*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE7,0x42,0x24,0x24,0x14,0x08,0x08,0x00,0x00},/*"v",86*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xEB,0x49,0x49,0x55,0x55,0x22,0x22,0x00,0x00},/*"w",87*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x76,0x24,0x18,0x18,0x18,0x24,0x6E,0x00,0x00},/*"x",88*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE7,0x42,0x24,0x24,0x14,0x18,0x08,0x08,0x07},/*"y",89*/{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7E,0x22,0x10,0x08,0x08,0x44,0x7E,0x00,0x00},/*"z",90*/{0x00,0xC0,0x20,0x20,0x20,0x20,0x20,0x10,0x20,0x20,0x20,0x20,0x20,0x20,0xC0,0x00},/*"{",91*/{0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10},/*"|",92*/{0x00,0x06,0x08,0x08,0x08,0x08,0x08,0x10,0x08,0x08,0x08,0x08,0x08,0x08,0x06,0x00},/*"}",93*/{0x0C,0x32,0xC2,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"~",94*/};      

配置好相应的IO为推挽输出，硬件初始化即可。不过这里需要注意的是，这里使用GPIOB作为I80总线数据口，所以和Jtag口冲突（详见：stm32 最小系统 中jtag说明）。所以在配置IO时要将 jtag口的IO复用关闭：

在GPIO_Configuration()配置中：GPIO_PinRemapConfig(GPIO_Remap_SWJ_Disable, ENABLE);// 改变指定管脚的映射 GPIO_Remap_SWJ_Disable SWJ 完全禁用（JTAG+SW-DP）;必须加上这句,否则会导致串口无法使用 被折腾了很久  原因不详GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable , ENABLE);// 改变指定管脚的映射 GPIO_Remap_SWJ_JTAGDisable ，JTAG-DP 禁用 + SW-DP 使能注意：不要忘记在RCC_Configuration()中开启AFIO时钟，//AFIO时钟RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE);

在main.c中直接调用相关函数：

int main(void){	//stm32 初始化			RCC_Configuration();	NVIC_Configuration();			USART_Configuration();	SPI_Configuration();	GPIO_Configuration();	LCD_Init();	POINT_COLOR = BLACK;	//设置字体颜色   		 	LCD_ShowString(30,50,"Hello Dog .. ");		printf("\r\n test.. \r\n");	while(1);  }

LCD显示效果：