我精心整理的一个温度传感器18B20的程序包,可直接调用
这个程序适用于12MHz晶振的51单片机,默认为89C52系列,如果是89C51的话,把头文件改为
#include "reg51.h"
就可以了,下面是头文件和C文件,大家在工程里加入C文件,在主程序中加入头文件,直接调用
read_temp();
函数,就可以返回浮点型的温度值,为10进制,可以处理后直接用LCD或数码管显示,很方便,是我做温控的子程序。
/*************头文件******************/
#include "reg52.h"
#include "intrins.h" //_nop_();延时函数用
#define uchar unsigned char
#define uint unsigned int
sbit DQ="P3"^4; //温度输入口
ow_reset(void);//18B20复位
void write_byte(uchar val);//写命令
uchar read_byte(void);//读数据
/***********读出温度函数**********
输入:无
输出:zs+xs,格式为123.4
即为浮点型数的温度格式
===================================*/
float read_temp();
/***************C文件**********************/
#include "reg52.h"
#include "18B20.h" //_nop_();延时函数用
//*******温度小数部分用查表法**********//
uchar code ditab[16]={0x00,0x01,0x01,0x02,0x03,
0x03,0x04,0x04,0x05,0x06,0x06,0x07,0x08,0x08,0x09,0x09};
/***********11微秒延时函数**********/
//
void delay(uint t)
{
for(;t>0;t--);
}
//
/***********18B20复位函数**********/
ow_reset(void)
{
char presence="1";
while(presence)
{
while(presence)
{
DQ=1;_nop_();_nop_();
DQ=0; //
delay(50); // 550us
DQ=1; //
delay(6); // 66us
presence=DQ; // presence="0继续下一步"
}
delay(45); //延时500us
presence = ~DQ;
}
DQ=1;
}
//
//
/**********18B20写命令函数*********/
//向 1-WIRE 总线上写一个字节
void write_byte(uchar val)
{
uchar i;
for (i=8; i>0; i--) //
{
DQ=1;_nop_();_nop_();
DQ = 0;_nop_();_nop_();_nop_();_nop_();_nop_();//5us
DQ = val&0x01; //最低位移出
delay(6); //66us
val=val/2; //右移一位
}
DQ = 1;
delay(1);
}
//
/*********18B20读1个字节函数********/
//从总线上读取一个字节
uchar read_byte(void)
{
uchar i;
uchar value = 0;
for (i=8;i>0;i--)
{
DQ=1;_nop_();_nop_();
value>>=1;
DQ = 0; //
_nop_();_nop_();_nop_();_nop_(); //4us
DQ = 1;_nop_();_nop_();_nop_();_nop_(); //4us
if(DQ)value|=0x80;
delay(6); //66us
}
DQ=1;
return(value);
}
//
/***********读出温度函数**********
输入:无
输出:zs+xs,格式为123.4
即为浮点型数的温度格式
===================================*/
//
float read_temp()
{
float zs,xs;//存放整数和小数
uchar temp_data[2];//读出温度暂存
EA=0;//禁止中断,防止读错
ow_reset(); //总线复位
write_byte(0xCC); // 发Skip ROM命令
write_byte(0xBE); // 发读命令
temp_data[0]=read_byte(); //温度低8位
temp_data[1]=read_byte(); //温度高8位
ow_reset();
write_byte(0xCC); // Skip ROM
write_byte(0x44); // 发转换命令
xs=ditab[temp_data[0]&0x0f];//小数位
xs=xs/10;
zs=((temp_data[0]&0xf0)>>4)|((temp_data[1]&0x0f)<<4);//整数位
return (zs+xs);
EA=1;//开中断
}
//结束
当然,大家做数字温度计的话直接使用这个程序就可以了,但是如果要做多点温控的话,大家还要自己写查找序列号的程序!加油!
/************************************************************
*18B20驱动程序,DQ为数据口,接于P2.1
*11.0592M晶振,上拉4.7k电阻
*Author:fyb
*2005-3-25 11:23,OK!
*************************************************************/
#i nclude<reg51.h>
#i nclude<intrins.h>
#define uchar unsigned char
#define uint unsigned int
sbit dq = P1^7;
bit flag;
uint Temperature;
uchar temp_buff[9]; //存储读取的字节,read scratchpad为9字节,read rom ID为8字节
uchar id_buff[8];
uchar *p;
uchar crc_data;
uchar code CrcTable [256]={
0, 94, 188, 226, 97, 63, 221, 131, 194, 156, 126, 32, 163, 253, 31, 65,
157, 195, 33, 127, 252, 162, 64, 30, 95, 1, 227, 189, 62, 96, 130, 220,
35, 125, 159, 193, 66, 28, 254, 160, 225, 191, 93, 3, 128, 222, 60, 98,
190, 224, 2, 92, 223, 129, 99, 61, 124, 34, 192, 158, 29, 67, 161, 255,
70, 24, 250, 164, 39, 121, 155, 197, 132, 218, 56, 102, 229, 187, 89, 7,
219, 133, 103, 57, 186, 228, 6, 88, 25, 71, 165, 251, 120, 38, 196, 154,
101, 59, 217, 135, 4, 90, 184, 230, 167, 249, 27, 69, 198, 152, 122, 36,
248, 166, 68, 26, 153, 199, 37, 123, 58, 100, 134, 216, 91, 5, 231, 185,
140, 210, 48, 110, 237, 179, 81, 15, 78, 16, 242, 172, 47, 113, 147, 205,
17, 79, 173, 243, 112, 46, 204, 146, 211, 141, 111, 49, 178, 236, 14, 80,
175, 241, 19, 77, 206, 144, 114, 44, 109, 51, 209, 143, 12, 82, 176, 238,
50, 108, 142, 208, 83, 13, 239, 177, 240, 174, 76, 18, 145, 207, 45, 115,
202, 148, 118, 40, 171, 245, 23, 73, 8, 86, 180, 234, 105, 55, 213, 139,
87, 9, 235, 181, 54, 104, 138, 212, 149, 203, 41, 119, 244, 170, 72, 22,
233, 183, 85, 11, 136, 214, 52, 106, 43, 117, 151, 201, 74, 20, 246, 168,
116, 42, 200, 150, 21, 75, 169, 247, 182, 232, 10, 84, 215, 137, 107, 53};
//
/************************************************************
*Function:延时处理
*parameter:
*Return:
*Modify:
*************************************************************/
void TempDelay (uchar us)
{
while(us--);
}
/************************************************************
*Function:18B20初始化
*parameter:
*Return:
*Modify:
*************************************************************/
void Init18b20 (void)
{
dq=1;
_nop_();
dq=0;
TempDelay(86); //delay 530 uS//80
_nop_();
dq=1;
TempDelay(14); //delay 100 uS//14
_nop_();
_nop_();
_nop_();
if(dq==0)
flag = 1; //detect 1820 success!
else
flag = 0; //detect 1820 fail!
TempDelay(20); //20
_nop_();
_nop_();
dq = 1;
}
/************************************************************
*Function:向18B20写入一个字节
*parameter:
*Return:
*Modify:
*************************************************************/
void WriteByte (uchar wr) //单字节写入
{
uchar i;
for (i=0;i<8;i++)
{
dq = 0;
_nop_();
dq=wr&0x01;
TempDelay(5); //delay 45 uS //5
_nop_();
_nop_();
dq=1;
wr >>= 1;
}
}
/************************************************************
*Function:读18B20的一个字节
*parameter:
*Return:
*Modify:
*************************************************************/
uchar ReadByte (void) //读取单字节
{
uchar i,u=0;
for(i=0;i<8;i++)
{
dq = 0;
u >>= 1;
dq = 1;
if(dq==1)
u |= 0x80;
TempDelay (4);
_nop_();
}
return(u);
}
/************************************************************
*Function:读18B20
*parameter:
*Return:
*Modify:
*************************************************************/
void read_bytes (uchar j)
{
uchar i;
for(i=0;i<j;i++)
{
*p = ReadByte();
p++;
}
}
/************************************************************
*Function:CRC校验
*parameter:
*Return:
*Modify:
*************************************************************/
uchar CRC (uchar j)
{
uchar i,crc_data=0;
for(i=0;i<j;i++) //查表校验
crc_data = CrcTable[crc_data^temp_buff[i]];
return (crc_data);
}
/************************************************************
*Function:读取温度
*parameter:
*Return:
*Modify:
*************************************************************/
void GemTemp (void)
{
read_bytes (9);
if (CRC(9)==0) //校验正确
{
Temperature = temp_buff[1]*0x100 + temp_buff[0];
// Temperature *= 0.625;
Temperature /= 16;
TempDelay(1);
}
}
/************************************************************
*Function:内部配置
*parameter:
*Return:
*Modify:
*************************************************************/
void Config18b20 (void) //重新配置报警限定值和分辨率
{
Init18b20();
WriteByte(0xcc); //skip rom
WriteByte(0x4e); //write scratchpad
WriteByte(0x19); //上限
WriteByte(0x1a); //下限
WriteByte(0x7f); //set 11 bit (0.125)
Init18b20();
WriteByte(0xcc); //skip rom
WriteByte(0x48); //保存设定值
Init18b20();
WriteByte(0xcc); //skip rom
WriteByte(0xb8); //回调设定值
}
/************************************************************
*Function:读18B20ID
*parameter:
*Return:
*Modify:
*************************************************************/
void ReadID (void)//读取器件 id
{
Init18b20();
WriteByte(0x33); //read rom
read_bytes(8);
}
/************************************************************
*Function:18B20ID全处理
*parameter:
*Return:
*Modify:
*************************************************************/
void TemperatuerResult(void)
{
p = id_buff;
ReadID();
Config18b20();
Init18b20 ();
WriteByte(0xcc); //skip rom
WriteByte(0x44); //Temperature convert
Init18b20 ();
WriteByte(0xcc); //skip rom
WriteByte(0xbe); //read Temperature
p = temp_buff;
GemTemp();
}
联系客服